Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last Post |
|
|---|---|---|---|
|
xps pre-lam epoxy sealer coat? (Page: 1, 2)
by TaylorO » 3 months 3 weeks ago |
13 | by McDing » 3 months 2 weeks ago » Go | |
|
7’3” Single-Fin Egg Tweaking by fetchcraft » 3 months 3 weeks ago |
7 | by fetchcraft » 3 months 2 weeks ago » Go | |
|
Da Bull is Gone by unclegrumpy » 3 months 2 weeks ago |
3 | by McDing » 3 months 2 weeks ago » Go | |
|
How much to charge for a nose snap? by mako224 » 3 months 3 weeks ago |
4 | by thrailkill » 3 months 2 weeks ago » Go | |
|
Switching from epoxy to poly by The_Pretzel » 3 months 3 weeks ago |
6 | by The_Pretzel » 3 months 2 weeks ago » Go | |
|
xos blank early stage by TaylorO » 3 months 3 weeks ago |
2 | by TaylorO » 3 months 2 weeks ago » Go | |
|
Resin curing times (Page: 1, 2)
by staegermeister » 3 months 3 weeks ago |
18 | by Huck » 3 months 3 weeks ago » Go | |
|
Misc Laminating questions (Page: 1, 2, 3 … Last Page)
by Fundito » 3 months 4 weeks ago |
44 | by Fundito » 3 months 3 weeks ago » Go | |
|
Behr Wet Look Sealer instead of second gloss coat by SDSG » 3 months 3 weeks ago |
9 | by deez » 3 months 3 weeks ago » Go | |
|
Anyone using auto ceramic coating for board bottoms? by GregTate » 3 months 3 weeks ago |
1 | by thrailkill » 3 months 3 weeks ago » Go | |
|
xps ding delam help? (Page: 1, 2, 3)
by TaylorO » 4 months 5 days ago |
21 | by TaylorO » 3 months 3 weeks ago » Go | |
|
Joe Quigg is gone by Honolulu » 3 months 3 weeks ago |
1 | by Huck » 3 months 3 weeks ago » Go | |
|
Colouring Stringer by saltbush » 3 months 3 weeks ago |
4 | by McDing » 3 months 3 weeks ago » Go | |
|
First Board! Assym (Page: 1, 2)
by woolmer » 3 months 3 weeks ago |
11 | by gdaddy » 3 months 3 weeks ago » Go | |
|
What the... by Surffoils » 3 months 3 weeks ago |
4 | by gdaddy » 3 months 3 weeks ago » Go | |
|
Installing a stringer on a foam board that's already been shaped out of the blank by kyle_freedman » 3 months 3 weeks ago |
3 | by McDing » 3 months 3 weeks ago » Go | |
|
All you CAD fin makers, where's the WAVE set fins? by Monkstar1 » 2 years 2 months ago |
3 | by vintageyouth » 3 months 3 weeks ago » Go | |
|
Front Rails by jackaroe » 3 months 4 weeks ago |
5 | by gdaddy » 3 months 3 weeks ago » Go | |
|
Waveset Adapter (Page: 1, 2)
by vintageyouth » 4 months 2 days ago |
15 | by SammyA » 3 months 4 weeks ago » Go | |
|
Laminating without Fiberglass, JUST Epoxy resin (Page: 1, 2)
by YoothAttack » 4 months 3 weeks ago |
20 | by McDing » 4 months 1 day ago » Go |
